Difference between revisions of "Teletype Model 33 SN xyz"
(Added WTB, goals) |
(→Help Resources: Added JJ Short & Associates) |
||
(8 intermediate revisions by the same user not shown) | |||
Line 5: | Line 5: | ||
[[File:Teletype Model 33.png|300px]] | [[File:Teletype Model 33.png|300px]] | ||
+ | |||
+ | ==Help Resources== | ||
+ | * GreenKeys is an email list devoted to the discussion of older radio teletype (RTTY) gear. [http://www.qth.net/mailman/listinfo/greenkeys subscribe here] | ||
+ | * [http://www.vintagecomputer.net/teletype101.cfm Teletype 101] at vintagecomputer.net | ||
+ | * Check the [[20ma current loop to RS-232 conversion]] page here on the Retrowagon wiki for some help with 20ma <> RS232 conversion. | ||
+ | * Typewriter Platens restoration, parts [http://www.jjshort.com/typewriter-platen-repair.php J.J. Short & Associates] (From Greenkeys) "... You will want 95 Shore A hardness and 1.1150 nominal finished O.D ..." | ||
==Wanted to buy== | ==Wanted to buy== | ||
Line 21: | Line 27: | ||
[[File:Teletype Model 33 Repair.png|500px]] | [[File:Teletype Model 33 Repair.png|500px]] | ||
+ | |||
+ | * 8/4/2015 electronics details | ||
+ | [[File:Teletype Model 33 KSR empty modem base.png|400px]] | ||
+ | [[File:Teletype Model 33 KSR view of electronics.png|400px]] | ||
+ | [[File:Teletype Model 33 cable detail.png|400px]] | ||
+ | |||
+ | Apparent current loop cable is attached to pins 1,2 and 7,8. There had been a DB25 connector on the bare end it's fallen off over the decades since last use. | ||
+ | |||
+ | ===Later in the evening=== | ||
+ | I need a spring to hold this bar up. I think it's called a "Function Pawl" ''Section 574-122-100TC'' | ||
+ | [[File:Teletype Model 33 Need Spring For This.png|400px]] | ||
+ | |||
+ | The piece I need the spring for goes in here somewhere! | ||
+ | [[File:Teletype Model 33 Need Spring.png|400px]] | ||
[[Category:Inoperative]] | [[Category:Inoperative]] | ||
[[Category:Serial Terminals]] | [[Category:Serial Terminals]] | ||
+ | [[Category:Teletype]] |
Latest revision as of 03:49, 18 January 2016
Contents
Teletype Model 33
This belonged to my Dad. I remember playing a lot of Startrek(.bas) on it when hooked up to the 'ol Imsai. I'd sure like to get it working. One problem I have with getting it working is I left it behind when I moved! (S/N xyz. It's in storage where I can't get at it at the moment.) I would also be nice to add paper tape to it too.
Teletype mode 33 Wikipedia article
Help Resources
- GreenKeys is an email list devoted to the discussion of older radio teletype (RTTY) gear. subscribe here
- Teletype 101 at vintagecomputer.net
- Check the 20ma current loop to RS-232 conversion page here on the Retrowagon wiki for some help with 20ma <> RS232 conversion.
- Typewriter Platens restoration, parts J.J. Short & Associates (From Greenkeys) "... You will want 95 Shore A hardness and 1.1150 nominal finished O.D ..."
Wanted to buy
- Roll(s) of paper tape
- Typewheel hammer ?felt?
- Call Control Unit plate under rotary dial with holes for buttons
Goals
- Restore to operation as an S-100 computer interface
I've got parts to make a 20ma current loop to RS-232C adapter, but hopefully will be able to resurrect something like an Imsai SIO S-100 card in current loop mode for authenticity.
Restoration History
- 7/30/2015 Retrieved my Dad's KSR and bought an ASR on the way home.
- 8/4/2015 electronics details
Apparent current loop cable is attached to pins 1,2 and 7,8. There had been a DB25 connector on the bare end it's fallen off over the decades since last use.
Later in the evening
I need a spring to hold this bar up. I think it's called a "Function Pawl" Section 574-122-100TC