Difference between revisions of "ABOOTSIM.ASM"
(Initial creation) |
(Add syntaxhighlight) |
||
| Line 1: | Line 1: | ||
| + | <syntaxhighlight lang="asm"> | ||
;ABOOTSIM.ASM VERSION 1.0 10/27/76 JRB | ;ABOOTSIM.ASM VERSION 1.0 10/27/76 JRB | ||
3 IMSAI CP/M SIMULATOR FOR AUTOMATIC BOOTSTRAP | 3 IMSAI CP/M SIMULATOR FOR AUTOMATIC BOOTSTRAP | ||
| Line 117: | Line 118: | ||
END BBASE | END BBASE | ||
| + | |||
| + | </syntaxhighlight> | ||
Revision as of 20:32, 1 August 2018
;ABOOTSIM.ASM VERSION 1.0 10/27/76 JRB
3 IMSAI CP/M SIMULATOR FOR AUTOMATIC BOOTSTRAP
;THIS PROGRAM IS ONLY NEEDED TO START CP/M COLD
; IF YOU DO NOT YET HAVE THE NEW AUTOMATIC BOOTSTRAP
; FIRMWARE INSTALLED IN YOUR DISC INTERFACE.
;THE FUNCTION OF THIS PROGRAM IS TO READ DRIVE 0,
3 TRACK a, SECTOR I INTO RAM LOCATIONS
; a To 7FH THEN JMP To 0.
;THIS IS THE FANCY VERSION,
; SUITABLE FOR USE IN ROM AND WITH ERROR RECOVERY.
BBASE EQU ROOOH ;ORIGIN AND STARTING ADDRESS
EXIT EQU o ;wHERE THIS PROGRAM EXITS To
DISK EQU OFDH ;COMMAND PORT FOR FLOPPY DISC
BCMD EQU 80H ;BEGINNING OF DISC COMMAND STRING
;AND COMMAND BYTE THEREOF
BSTAT EQU BCMD+1 ;STATUS BYTE... I
BTRK EQU BCMD+2 ;TRACK (2 BYTES)
IBSECT EQU GCMD+4 ;SECTOR
BBUFAD EQU BCMD+5 ;BUFFER ADDRESS
ORG BBASE
3
; START HERE
3
3 SET FLOPPY DISC INTERFACE STRING POINTER
MVI A,IOH ;COMMAND TO SET STRING POINTER 0
our DISK ;SEND IT ‘
LXI H,BCMD ;POINT H AT COMMAND STRING
Mov A,L 5L0 ORDER STRING ADDRESS
OUT DISK
Mov A,H ;HI ORDER STRING ADDRESS
OUT DISK
; ABOOTSIM.ASM CONTINUED
;SET UP STRING IN RAM
5
MVI M,21H
INX H
;COMMAND TO READ SECTOR, UNIT 0
,POINT AT STATUS BYTE
5(3TATUS BYTE WILL BE ZEROED LATER)
INX H ,POINT AT HI ORDER TRACK
XRA A ;CET 0 IN A
Mov M,A 3ZERO HIGH ORDER TRACK
INX H
MOv M,A ;ZERO LO ORDER TRACK
INX H
MVI M,1 ;SECTOR 1
INX H
Mov M,A ;2ERO LO ORDER BUFFER ADDRESS
INX H
Mov M,A ;ZERO HIGH ORDER BUF ADDRESS
; INITIALIZATION COMPLETE. NOW READ SECTOR.
REPEAT: LXI
WAIT:
H,BSTAT
XRA A .
MOV M,A ;STATus MUST BE 0 BEFORE COMMAND
;N. B. A=o IS DISK COMMAND TO EXECUTE STRING 0
OUT DISK 3TELL DISK TO GO!
ADD M ;LOOK FOR NON-0 STATUS
JZ WAIT ;KEEP LOOKING TILL IT COMES
CPI I ;ONLY CORRECT RETURN VALUE IS 1
J2 EXIT ;ON SUCCESS, TRANSFER CONTROL
;CP/M BOOTSTRAP ROUTINE READ IN FROM DISK
; DISK ERROR HAS OCCURED. -
3 DISPLAY ERROR CODE IN LIGHTS AND KEEP TRYING.
V. 50 5.
THUS IF DISK IS NOT READY,
CP/M WILL BOOT AS SOON AS IT COMES READY.
CMA 5LIGHTS DISPLAL COMPLEMENT
OUT OFFH 5OUTPUT A TO "PROG OUTPUT" LIGHTS
MVI A,21H ;RESTORE DRIVE 1 - IT HELPS!
OUT DISK ;SEND RESTORE COMMAND TO DISK
JMP REPEAT 3TRY AGAIN (AND AGAIN, AND ...)
END BBASE
