ABOOTSIM.ASM

; JHA 8/1/2018
; OCR'ed from IMSAI_CPM_System_Users_Guide_Version_1.31_Rev_2_Mar77.pdf
;
;ABOOTSIM.ASM VERSION 1.0 10/27/76 JRB
; IMSAI CP/M SIMULATOR FOR AUTOMATIC BOOTSTRAP

;THIS PROGRAM IS ONLY NEEDED TO START CP/M COLD
; IF YOU DO NOT YET HAVE THE NEW AUTOMATIC BOOTSTRAP
; FIRMWARE INSTALLED IN YOUR DISC INTERFACE.

;THE FUNCTION OF THIS PROGRAM IS TO READ DRIVE 0,
; TRACK a, SECTOR I INTO RAM LOCATIONS
; a To 7FH THEN JMP To 0.

;THIS IS THE FANCY VERSION,
; SUITABLE FOR USE IN ROM AND WITH ERROR RECOVERY.

BBASEE  QU 4OOOH ;ORIGIN AND STARTING ADDRESS
EXIT    EQU 0 ;wHERE THIS PROGRAM EXITS To
DISK    EQU OFDH ;COMMAND PORT FOR FLOPPY DISC
BCMD    EQU 80H ;BEGINNING OF DISC COMMAND STRING
;AND COMMAND BYTE THEREOF
BSTAT   EQU BCMD+1 ;STATUS BYTE... I
BTRK    EQU BCMD+2 ;TRACK (2 BYTES)
IBSECT  EQU GCMD+4 ;SECTOR
BBUFAD  EQU BCMD+5 ;BUFFER ADDRESS
ORG BBASE

;
; START HERE
;

; SET FLOPPY DISC INTERFACE STRING POINTER

        MVI A,10H   ;COMMAND TO SET STRING POINTER 0
        OUT DISK    ;SEND IT ‘
        LXI H,BCMD  ;POINT H AT COMMAND STRING
        MOV A,L     ;LO ORDER STRING ADDRESS
        OUT DISK
        MOV A,H     ;HI ORDER STRING ADDRESS
        OUT DISK

        ; ABOOTSIM.ASM CONTINUED

        ;SET UP STRING IN RAM

        MVI M,21H   ;COMMAND TO READ SECTOR, UNIT 0
        INX H       ;POINT AT STATUS BYTE
                    ;(STATUS BYTE WILL BE ZEROED LATER)

        INX H       ;POINT AT HI ORDER TRACK
        XRA A       ;GET 0 IN A
        MOV M,A     ;ZERO HIGH ORDER TRACK
        INX H
        MOv M,A     ;ZERO LO ORDER TRACK
        INX H
        MVI M,1     ;SECTOR 1
        INX H
        MOV M,A     ;ZERO LO ORDER BUFFER ADDRESS
        INX H
        MOV M,A     ;ZERO HIGH ORDER BUF ADDRESS

; INITIALIZATION COMPLETE. NOW READ SECTOR.

REPEAT: LXI H,BSTAT
        XRA A 
        MOV M,A     ;STATus MUST BE 0 BEFORE COMMAND
        ;N. B. A=o IS DISK COMMAND TO EXECUTE STRING 0
        OUT DISK    ;TELL DISK TO GO!
WAIT:   ADD M       ;LOOK FOR NON-0 STATUS
        JZ WAIT     ;KEEP LOOKING TILL IT COMES
        CPI I       ;ONLY CORRECT RETURN VALUE IS 1
        JZ EXIT     ;ON SUCCESS, TRANSFER CONTROL
            ;CP/M BOOTSTRAP ROUTINE READ IN FROM DISK

;
; DISK ERROR HAS OCCURED.
; DISPLAY ERROR CODE IN LIGHTS AND KEEP TRYING.
;THUS IF DISK IS NOT READY,
;CP/M WILL BOOT AS SOON AS IT COMES READY.
;
        CMA         ;LIGHTS DISPLAL COMPLEMENT
        OUT OFFH    ;OUTPUT A TO "PROG OUTPUT" LIGHTS
        MVI A,21H   ;RESTORE DRIVE 1 - IT HELPS!
        OUT DISK    ;SEND RESTORE COMMAND TO DISK
        JMP REPEAT  ;TRY AGAIN (AND AGAIN, AND ...)

        END BBASE